Satel INTEGRA Plus Spécifications Page 50
- Page / 82
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
48 Programming SATEL
5. F
IRE
(
FROM KEYPAD
) – signals the fire alarms triggered from keypad.
6. P
ANIC
(
FROM KEYPAD
) – signals the loud panic alarms triggered from keypad.
7. M
EDICAL ALARM
(
FROM KEYPAD
) – signals the medical assistance call alarm triggered from
keypad.
8. T
AMPER ALARM
– signals the tamper alarms.
9. DAY
ALARM
– signals the following:
– alarms from 13. PANIC-
SILENT
type zones,
– medical alarms from the 14. M
EDICAL
-
B
UTTON
and 15. P
ERSONAL EMERGENCY
type
zones,
– alarms from 7. D
AY
/N
IGHT
type zones, if the partition to which the zone belongs is
disarmed,
– alarms from 8. E
XTERIOR
type zones, if the armed mode which assumes that the user
will stay inside the protected facility is enabled in the partition (see: U
SER MANUAL
),
– alarms from 4. P
ERIMETER
type zones, if the S
IGNALING DELAY
has been programmed for
them,
– alarm from 5. I
NSTANT
and 6. E
XIT
type zones, if the B
ELL DELAY
option has been
enabled and the S
IGNALING DELAY
has been programmed for them,
– alarms from zones, for which the R
EPORTING DELAY
option has been enabled, provided
they were violated during the E
NTRY DELAY
countdown,
– unverified alarms, if the A
UDIBLE ALARM AFTER VERIFICATION
option is enabled for the
partition,
– the first violation of the 8.
E
XTERIOR
type zones when they are armed, provided the
S
URVEILLANCE TIME
has been programmed for the zone,
– violation of the counting zones (16-31 type zones) when armed.
10. DURESS
ALARM
– action carried out under duress – signals that a DURESS type code
(or prefix) has been used in the system.
11. C
HIME
– signals violation of the zones when they are disarmed.
12. S
ILENT ALARM
– activates in the same situations as the 9. DAY
A
LARM
output. Additionally,
it can signal silent panic alarms.
13. T
ECHNICAL ALARM
– signals alarms from zone types 40-56.
14. Z
ONE VIOLATION
– indicates the violations of zones.
15. V
IDEO ON DISARMED
– controlled by zones with the V
IDEO ON DISARMED
option enabled.
16. V
IDEO ON ARMED
– controlled by zones with the V
IDEO ON ARMED
option enabled.
17. READY
STATUS
– indicates whether the system is ready for arming, i.e. whether there are
no violated zones (active when there is no violation).
18. BYPASS
STATUS
– indicates the bypassing of zones.
19. E
XIT DELAY STATUS
– indicates the E
XIT DELAY
countdown.
20. E
NTRY DELAY STATUS
– indicates the E
NTRY DELAY
countdown.
21. A
RMED STATUS
– indicates the armed status of partitions.
22. F
ULL ARMED STATUS
– active if all selected partitions are armed.
23. A
RM
/D
ISARM BEEP
– signals:
– starting the arming procedure (arming, if the exit delay has not been programmed) –
1 pulse;
– disarming – 2 pulses;
– clearing alarm – 4 pulses;
– denial of arming or arming procedure failure – 7 pulses.
- PROGRAMMING 1
- 2 Programming SATEL 4
- SATEL INTEGRA Plus 3 5
- 1. General 6
- 2. Programming options 6
- 2.1.5 Service mode menu 7
- 6 Programming SATEL 8
- SATEL INTEGRA Plus 7 9
- 8 Programming SATEL 10
- SATEL INTEGRA Plus 9 11
- [n – counter number] 11
- SATEL INTEGRA Plus 11 13
- [n – identifier number] 13
- 12 Programming SATEL 14
- SATEL INTEGRA Plus 13 15
- 14 Programming SATEL 16
- SATEL INTEGRA Plus 15 17
- 16 Programming SATEL 18
- SATEL INTEGRA Plus 17 19
- (only INT-S and INT-SK) 19
- (only INT-SCR) 19
- [n – number of output] 19
- 18 Programming SATEL 20
- SATEL INTEGRA Plus 19 21
- (does not apply to CA-64 DR) 21
- 20 Programming SATEL 22
- SATEL INTEGRA Plus 21 23
- 22 Programming SATEL 24
- 2.2 DLOADX program 25
- 24 Programming SATEL 26
- SATEL INTEGRA Plus 25 27
- 26 Programming SATEL 28
- program 29
- 28 Programming SATEL 30
- SATEL INTEGRA Plus 29 31
- LOADX program 32
- Configuring the GSM module 33
- Initiating a connection 33
- 3. System structure 34
- 3.2.3 Partition parameters 35
- Partition type 36
- Options 37
- 3.3 Zones 38
- 3.3.3 Programming the zones 39
- 3.3.4 Zone parameters 39
- 38 Programming SATEL 40
- SATEL INTEGRA Plus 39 41
- 3.3.5 Zone types 42
- SATEL INTEGRA Plus 41 43
- 3.3.6 Zone options 44
- SATEL INTEGRA Plus 43 45
- 44 Programming SATEL 46
- 3.3.7 Counters 47
- 3.3.8 Bypasses 47
- 4. Outputs 48
- 4.1 Output parameters 49
- 4.2 Output functions 49
- 48 Programming SATEL 50
- SATEL INTEGRA Plus 49 51
- 50 Programming SATEL 52
- SATEL INTEGRA Plus 51 53
- 4.3 Options 54
- 4.4 Output triggering 54
- 4.6 Output disabling 55
- 4.8 Output groups 56
- 4.9 Output state indicating 57
- 4.11 Output testing 57
- 5. System options 58
- 5.2 Printer options 59
- 5.3 Other options 60
- SATEL INTEGRA Plus 59 61
- 4 Arming options 62
- Times 5.5 63
- 5. r parameters 63
- 62 Programming SATEL 64
- 6. Programming the keypads 65
- 64 Programming SATEL 66
- SATEL INTEGRA Plus 65 67
- 66 Programming SATEL 68
- 7. Timers 69
- 8. User schedules 70
- 9. Reporting 70
- SATEL INTEGRA Plus 69 71
- 9.1.2 Advanced options 72
- Identifiers 73
- SIA / TELIM prefix 74
- Events assignment 74
- 9.1.4 SIA-IP 74
- 9.1.6 Event codes 74
- 9.2 Starting the reporting 75
- 9.2.3 GPRS reporting 76
- 10. Messaging 77
- 76 Programming SATEL 78
- 10.2.1 Events assignment 79
- 78 Programming SATEL 80
- SATEL INTEGRA Plus 79 81
- 13. Manual update history 82
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Satel INTEGRA Plus
(27 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.290 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels